Brivis Error Code 56, Pressure Switch Lockout

Brivis error code 56 means the heater has locked out because its pressure switch did not confirm safe flue airflow.

The manual links it most often to a restricted flue, and on StarPro Max and StarPro 6 models to a blocked condensate drain. Because flue gases must leave the home safely, this code deserves careful attention. This page explains how the pressure switch works, what you can check and what a technician will do.

What does Brivis error code 56 mean?

Code 56 is a pressure switch lockout. Before the burners light, a small combustion fan pushes or draws air through the heater and out of the flue. A pressure switch senses that airflow. If the switch does not confirm the right pressure, the heater will not light, and after the set number of tries it locks out with code 56.

The pressure switch is a safety device. It makes sure combustion gases have a clear path out of the home before any gas burns.

What are the common causes?

The manual points to two main causes.

  • A restriction in the flue, such as a bird nest, leaves, a damaged flue cap or a crushed flue pipe.
  • On StarPro Max and StarPro 6 models, a blocked condensate drain.

Other causes include a failing combustion fan, a cracked or disconnected pressure switch tube, a faulty pressure switch or a wiring fault.

Why do condensing models have a condensate drain?

High efficiency heaters such as the StarPro 6 and the older StarPro Max extract so much heat from the flue gases that water vapour in those gases condenses into liquid. That water must drain away through a condensate pipe. If the pipe blocks with debris, sludge or ice, water backs up inside the heater. The rising water can interfere with the flue path and the pressure switch, which triggers code 56.

StarPro 4 and StarPro 5 models are non condensing, so they do not need a condensate drain. On those models, focus on the flue.

What can you check safely?

Owners can make a few safe checks from outside.

  • Look at the flue terminal on the roof or wall and see whether anything obvious blocks it.
  • Clear loose leaves or debris from around an external heater, without opening it.
  • On StarPro 6 and StarPro Max models, find where the condensate pipe ends and check it is not buried, crushed or blocked at the outlet.

Do not climb onto the roof to reach a flue, and do not remove the flue cap or any heater panel. Those jobs need a licensed gas fitter.

How do birds and insects block flues?

Birds sometimes nest in flue terminals during spring and summer, when heaters sit idle. Wasps and other insects build nests too. When the heater starts in autumn, the nest restricts the flue and the pressure switch cannot confirm airflow. This is a very common cause of code 56 at the start of the heating season.

Fitting a proper flue terminal guard and booking a pre winter service reduces the risk.

Can wind cause code 56?

Strong wind blowing across or into a flue terminal can change the pressure the switch senses. On exposed sites, gusty nights can trigger occasional lockouts even when the flue is clear. If code 56 appears only during strong wind, mention this when you book. A technician may check the flue terminal type and position.

Can ice block a condensate drain?

In very cold inland areas, a condensate pipe running outside can freeze. In most of Sydney this is rare, although it can happen in colder elevated suburbs on frosty mornings. More often, condensate drains block with sludge, debris or insects at the outlet.

Is code 56 dangerous?

The lockout prevents the heater lighting when flue airflow is uncertain, so the safety system is doing its job. However, never try to bypass it or keep resetting it. A heater that burns gas with a blocked flue could allow combustion gases into the home. If anyone in the home feels unwell, dizzy or develops a headache while the heater runs, turn it off, ventilate and seek medical help.

How do you reset after code 56?

Once you have checked the flue terminal and condensate outlet, you can reset once using our reset guide. If code 56 returns, stop and call a technician.

What does a technician check?

First, the technician inspects the flue from the terminal back to the heater, looking for blockages, damage and poor joints. Next, they check the condensate drain on condensing models and clear it if needed. Then they test the combustion fan, the pressure switch and its tubing, and the wiring to the control board. Finally, they explain the cause and quote before any repair.

How long does a repair take?

Clearing a nest or a condensate blockage can be quick when access is easy. Replacing a pressure switch or tube is usually straightforward. A combustion fan or a damaged flue section may take longer, especially if parts must be ordered or roof access is difficult.

How can you prevent code 56?

Book a service before winter, keep the area around external heaters and flue terminals clear and ask about a flue guard if birds are common around your home. For StarPro 6 and StarPro Max owners, make sure the condensate drain outlet stays clear and is not covered by garden beds or mulch.

What is the difference between a flue and a flue terminal?

The flue is the pipe that carries combustion gases from the heater to the outside air. The flue terminal is the cap or fitting at the end of that pipe, on the roof, an outside wall or the heater cabinet for external models. Terminals are designed to let gases out while keeping rain, birds and debris out. A damaged or missing terminal lets things in, which can lead to code 56.

When you check from the ground, look at the terminal for obvious damage, nests or leaves. Never climb up to it.

What does flue vapour mean?

On cold days you may see white vapour drifting from the flue terminal while the heater runs. The manual describes this as normal. It is mostly water vapour from burning gas, and it shows more on cold, still mornings. A hot flue terminal is also normal. Neither of these causes code 56. Our flue steam guide explains more.

However, if you see dark staining around the terminal, smell fumes indoors or notice the vapour pouring from an unusual spot, turn the heater off and call us.

Can a gutter or roof change affect the flue?

Yes. New gutters, roof sheeting or solar panels can end up close to a flue terminal, changing how air moves around it. In some cases, a roofer may accidentally bend or crush a flue section. If code 56 starts soon after roof work, tell the technician what work was done and when.

How do we test the system after a repair?

After clearing a blockage or replacing a part, we run the heater through several full start cycles. We confirm the combustion fan reaches the right pressure, the pressure switch closes promptly and the burners light cleanly. Then we let the heater run and check the flue for proper discharge and the condensate drain for steady flow on condensing models. Only then do we hand the system back.

What should you do if the heater is under warranty?

If your heater is young, the warranty may cover a faulty pressure switch or combustion fan. Note that Brivis does not warrant the ductwork or the installation itself, and a flue blocked by a nest is not a product fault. Have your purchase details ready, and we can help you work out the next steps.

Is code 56 common on external heaters?

External heaters such as the Buffalo range have their flue built into the cabinet. Because the whole unit sits outside, leaves, insects and wind affect it directly. Keep the area around an external heater clear, and do not stack items against it or plant shrubs that grow over the flue outlet.

Why is code 56 more common in autumn?

Across spring and summer, heaters sit idle while birds nest, insects settle and leaves pile up. In addition, condensate drains can dry out and collect debris. When the first cold evenings arrive in autumn, the heater starts with all of that in place. As a result, autumn is the busiest time for code 56 callouts. A service booked in late summer or early autumn clears these problems before you need the heat, and it gives you time to fix anything the technician finds.

How do you book?

Call 02 9071 1142 and tell us you have code 56, the heater model and whether it is internal or external. You can also use our contact page, and we will call you back to arrange a convenient time for the visit.

How does the combustion fan fail?

The combustion fan, sometimes called an inducer, runs at the start of every heating cycle. Over years, its bearings wear and its motor weakens. A tired fan may still spin but not quite reach the airflow the pressure switch needs. In that case, the heater might light on some days and lock out on others. A technician can measure the pressure the fan produces and compare it with the switch setting.

What about the pressure switch tube?

A small flexible tube connects the pressure switch to a sensing point on the heater. Over time, that tube can crack, harden, kink or fill with condensation. If it does, the switch never sees the true pressure. Replacing the tube is a simple job for a technician and often fixes intermittent code 56 lockouts.

Can the pressure switch itself fail?

Yes. The switch contains a diaphragm and electrical contacts. The diaphragm can stiffen or tear, and the contacts can wear. Testing involves checking the switch against a known pressure and confirming it opens and closes at the right point. If it fails, a technician replaces it with the correct part for the model.

Why might code 56 appear after a renovation?

Roof work, new gutters, solar panel installations and extensions can all affect a flue. A flue terminal might end up too close to a new structure, or the flue pipe might be bumped or crushed in the roof. In addition, renovation dust can enter the heater. If code 56 appears after building work, mention exactly what changed.

Does flue position matter?

Flues must terminate in positions that allow combustion gases to disperse safely, with clearances from windows, doors and other openings set by installation rules. If a new window or pergola now sits near the flue, the heater may need its flue checked or modified. A licensed gas fitter can advise.

What if the heater is under the floor?

Underfloor heaters have flue runs through the subfloor and out to the open air. Those runs can collect water, debris or animal nests. Access is often tight, so leave inspection to a technician.

How does a condensate pump fit in?

Some condensing installations cannot drain by gravity and use a small pump. If that pump fails, water backs up and code 56 can follow. A technician checks the pump, its reservoir and its power supply.

Can a service catch flue problems early?

Yes. A service includes a check of the flue path, the combustion fan and the pressure switch. On condensing models, it includes the condensate drain. Brivis recommends servicing at least every two years. Our service page explains what the visit covers.

Frequently asked questions

What does Brivis code 56 mean?

A pressure switch lockout, usually caused by a flue restriction.

Can a condensate drain cause code 56?

Yes, on StarPro Max and StarPro 6 models, which have condensate drains.

Do StarPro 5 heaters have condensate drains?

No. StarPro 4 and StarPro 5 models are non condensing.

Can birds cause code 56?

Yes. Nests in flue terminals are a common cause at the start of winter.

Should I keep resetting?

No. Reset once after outside checks, then call a technician if it returns.

How do I book a technician?

Call 02 9071 1142 or use our contact page.

{“@context”:”https://schema.org”,”@type”:”HVACBusiness”,”@id”:”https://brivis.sydneyaircare.com.au/#business”,”name”:”Sydney Air Care, Brivis Service”,”url”:”https://brivis.sydneyaircare.com.au/”,”description”:”Brivis ducted heating and cooling repair, service and troubleshooting across Sydney. Independent service provider, not affiliated with Brivis.”,”areaServed”:[{“@type”:”City”,”name”:”Sydney”},{“@type”:”State”,”name”:”New South Wales”}],”parentOrganization”:{“@type”:”Organization”,”name”:”Sydney Air Care”,”url”:”https://sydneyaircare.com.au/”},”telephone”:”+61 2 9071 1142″} {“@context”:”https://schema.org”,”@type”:”FAQPage”,”mainEntity”:[{“@type”:”Question”,”name”:”What does Brivis code 56 mean?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”A pressure switch lockout, usually caused by a flue restriction.”}},{“@type”:”Question”,”name”:”Can a condensate drain cause code 56?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Yes, on StarPro Max and StarPro 6 models, which have condensate drains.”}},{“@type”:”Question”,”name”:”Do StarPro 5 heaters have condensate drains?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”No. StarPro 4 and StarPro 5 models are non condensing.”}},{“@type”:”Question”,”name”:”Can birds cause code 56?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Yes. Nests in flue terminals are a common cause at the start of winter.”}},{“@type”:”Question”,”name”:”Should I keep resetting?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”No. Reset once after outside checks, then call a technician if it returns.”}},{“@type”:”Question”,”name”:”How do I book a technician?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Call 02 9071 1142 or use our contact page.”}}]}
Call 02 9071 1142