Brivis Heater FAQ for Sydney Owners
This Brivis heater FAQ answers the questions Sydney owners ask us most often. Some answers save a call, such as how to clear a lockout or why the fan starts late. Others help you prepare for a visit or plan ahead for winter. Each answer is short, with a link to a fuller guide where one exists.
How should you use this Brivis heater FAQ?
Scan the section headings to find your topic, then read the short answers. If an answer links to a guide, follow it for the full detail. If you smell gas at any point, stop reading and follow the steps in our gas smell guide.
Codes and resets
What does code 40 mean?
Codes 40, 41, 42 and 43 mean the heater has overheated. The fan runs at maximum speed to cool it. Open outlets, clean the filter and reset. Our overheat page explains more.
What do codes 46, 47 and 55 mean?
The heater failed to light. Check that the gas is on at the meter and heater tap and that other gas appliances work. Our ignition codes page covers the details.
What does code 50 mean?
The heater locked out after four failed ignition attempts. Reset it once, but expect another lockout unless the underlying ignition cause is fixed.
What does code 56 mean?
A pressure switch lockout, usually from a flue restriction or, on StarPro Max and StarPro 6 models, a blocked condensate drain.
How do you reset a StarPro heater?
Press Reset beside Key 4. If it is not shown, press FN, Key 1, then Key 4. If the fault persists, turn the Networker off for two minutes, then switch off the heater power for about a minute. Our reset guide has the full steps.
How do you reset a Classic heater?
Turn the wall control off for five seconds and on again, three times within one minute.
Everyday use
Why does the fan start a minute after the burners?
The burners warm the heat exchanger first, so you do not get a blast of cold air. That short delay is completely normal.
Why does the fan keep running after heating stops?
It clears leftover heat from the heater. On StarPro models, a low fan may also run between cycles.
Is steam from the flue normal?
Yes. The manual describes flue vapour and a hot flue terminal as normal. Our flue steam guide explains more.
Why is the program running at the wrong time?
A long power cut may have reset the Networker clock. Set the time and day again on the master controller.
What is the default Networker PIN?
The first time default PIN is 1111. Press FN then Key 2 to lock or unlock.
Airflow and comfort
How often should you clean the return air filter?
Brivis says every fortnight during the heating season. Our filter guide shows how.
How many outlets should stay open?
At least the minimum shown in the outlet chart for your heater model. Our outlet guide explains the charts.
Why is one room always cold?
Usually the outlet, zone damper or duct to that room. Our cold rooms guide explains the checks.
How many zones can you have?
ZonePlus supports up to four independent zones on compatible heaters.
Why does the heater turn on and off so often?
Short cycling usually points to overheating from restricted airflow, a controller in a warm spot or a flame sensor fault. Our short cycling guide explains how to time the cycles.
Why does the air feel only warm, not hot?
Ducted heaters deliver large volumes of gently warm air, and modulating models turn down their flame as the home warms. If the home reaches the set temperature, the heater is working.
Can you run the fan without heat?
Yes. On StarPro models, Key 1 runs continuous fan, which circulates air without lighting the burners.
What is the best temperature to set?
Many households find somewhere around twenty degrees comfortable in living areas, with less in bedrooms overnight. Each degree lower saves gas.
Safety
What should you do if you smell gas?
Do not use switches or flames. Turn off the gas at the meter if safe, ventilate, leave and call your gas distributor or emergency services from outside.
Is a burning smell normal?
A faint dusty smell on the first start of winter is common and fades within an hour. Electrical or lasting burning smells are not normal. Turn the heater off and call us.
Do gas heaters produce carbon monoxide?
A properly working heater vents combustion gases safely through the flue. A cracked heat exchanger or blocked flue can let carbon monoxide into the home, and it has no smell. Regular servicing is the main protection.
Can you open the heater to look inside?
No. Leave anything inside the cabinet to a licensed gas fitter.
Cooling
Can the heater ducts be used for cooling?
Yes, with Brivis ICE add on refrigerated cooling. Evaporative coolers need separate ducts.
What does the snowman symbol mean?
Add on cooling is running. A flashing snowman means the compressor is in a delay period.
Why does an evaporative cooler need windows open?
Cooled air must push warm air out of the home. Without ventilation, cooling fades and humidity rises.
Why does a new cooler smell?
New Celdek pads give off a mild smell that fades as they are flushed during use.
Servicing and warranty
How often should a Brivis heater be serviced?
At least every two years by a licensed technician, as Brivis recommends. Brivis also suggests cleaning ducts every three years.
What warranty applies?
Most StarPro, Buffalo BX5C and Compact models carry five years parts and labour, with ten years on the burner, heat exchanger and structural parts.
Is servicing covered by warranty?
No. Servicing is chargeable, though proper maintenance is a warranty condition.
Who owns Brivis?
Brivis has been a brand of Rinnai Australia since 2014.
Ownership
How long does a Brivis heater last?
Lifespan depends on use, servicing and installation quality. In fact, Brivis notes some of its earliest gas heaters are still running nearly 50 years on. However, most households plan for replacement when major parts fail or efficiency falls well behind newer models. Meanwhile, regular servicing extends the life of any heater.
Is it worth repairing an older heater?
Often, yes. For example, sensors, igniters, fan capacitors and duct repairs are usually affordable. However, a cracked heat exchanger or several failing major parts on an old heater may justify replacement. Therefore, we always set out both options with clear costs.
Can you add zoning to an existing heater?
Usually, if the heater is compatible. ZonePlus works with StarPro heaters produced after a certain date and selected Buffalo models. Nevertheless, the ducts must suit the change, so the installer checks airflow first.
Can you add cooling later?
Yes, with Brivis ICE, if the heater and ducts suit it. Brivis notes cooling can be added later if the ducts were sized for it. Otherwise, duct changes may be needed.
Can you control the heater from a phone?
With a compatible controller and a wifi module, yes, through the Rinnai Touch app. However, older Networkers may not support it, so ask us to check your system.
Does a gas heater need a separate gas line?
It needs a gas supply large enough for the heater plus your other gas appliances. Consequently, if the line is too small, the heater may struggle to light or run weakly when other appliances run. A licensed gas fitter can check and upgrade the line.
Should the heater be turned off in summer?
Yes, unless you use the fan or add on cooling. In addition, before winter, run a test start and work through our winter start up checklist.
What should tenants do if the heater fails?
First, make the safe owner checks, such as the filter, outlets and controller. Then, report the fault to the property manager, who arranges repairs. Above all, tenants should not arrange gas work themselves without approval.
How do you find the heater model?
Look for the data plate on the cabinet, usually near the gas connection. For roof or underfloor heaters, do not climb in. Instead, check your paperwork or let the technician confirm it on site. Our models page explains the ranges.
What happens during a power cut?
Safety controls shut off the gas. Afterwards, when power returns, the heater resumes. Our power outage guide covers clocks and surges.
Costs and running
What does a repair cost?
It depends on the fault, the parts and access. For example, cleaning burners or replacing an igniter usually costs far less than a gas valve or control board. Therefore, we diagnose first and quote before any work. Our pricing page explains how we structure fees.
How can you lower gas bills?
Set a moderate temperature, use the program to lower it when the home is empty or everyone is asleep, keep the filter clean and use zones sensibly. In addition, close curtains at dusk and seal draughts. Over a winter, these habits add up to real savings.
Does a higher star rating really save gas?
Yes. Brivis notes each step up in star rating means roughly ten percent lower annual energy use. Consequently, a 6 star StarPro 6 uses noticeably less gas than an older 3 star heater for the same warmth.
Does continuous fan use much power?
The fan is the main electrical load of a ducted heater, so continuous fan uses electricity all the time it runs. Use it when it improves comfort, and turn it off when it does not.
How much water does an evaporative cooler use?
According to Brivis, consumption depends on the weather, the model size, the settings and the water management system. Hot, dry days use the most water but also give the best cooling.
Seasonal care
When is the best time to service a heater?
Autumn, before the first cold nights. Otherwise, you may wait longer once winter demand peaks.
When is the best time to service a cooler?
Spring, before the first heatwave. Similarly, booking early avoids the summer rush.
What should you check before winter?
Clean the filter, check outlets, confirm the gas supply, look at the flue from the ground, set the controller clock and run a test start.
What should you check before summer?
For add on cooling, clean the filter and clear the outdoor unit. For evaporative coolers, turn on the water supply, check the breaker and run the cooler with windows open.
Areas and visits
Which areas do you cover?
We cover Greater Sydney, including the Eastern Suburbs, the North Shore, South Sydney and Western Sydney. Our areas page lists the regions.
How long does a typical visit take?
Most services and simple repairs take one to two hours. However, roof access, duct work or ordered parts can extend the time, and the technician explains the timeline on the day.
Do you work with property managers?
Yes. We coordinate access with tenants, send quotes to whoever approves them and invoice the right party.
Do you work on other heating brands?
This site focuses on Brivis, although our wider team works on many brands. Mention any other systems when you book, and we can often check them on the same visit.
Booking
What should you have ready when you call?
The heater model, any code, what you have checked and where the heater is installed. In addition, photos of the controller screen and data plate help us prepare, and a note about access, parking and pets makes the visit smoother.
How do you book?
Call 02 9071 1142 or use our contact page. We will suggest safe checks and book a time that suits you.
Frequently asked questions
What does Brivis code 50 mean?
The heater locked out after four failed ignition attempts.
How often should I clean the filter?
Every fortnight during the heating season.
Is steam from the flue normal?
Yes. Flue vapour and a hot flue terminal are normal.
How often should I service my Brivis?
At least every two years.
What is the default Networker PIN?
1111 for first time use.
How do I book?
Call 02 9071 1142 or use our contact page.