Brivis Cooler Fault Message on the Networker
A Brivis cooler fault message appears on the Networker when a Brivis evaporative cooler on the roof detects a problem.
The message scrolls across the top of the screen, includes a code number and suggests calling for assistance. Some faults clear with a simple reset, while others point to the pump, the water supply, the fan or the controls. This page explains how to respond and what to check before booking a technician.
What does the Brivis cooler fault message look like?
On a Networker, the message scrolls across the top of the screen. It usually reads along the lines of a cooler fault with a code number and a prompt to call Brivis for assistance. The exact wording varies with the problem. Above all, the code number is the key detail, so write it down before you do anything else.
How do you reset after a cooler fault?
The Networker manual suggests pressing Key 4, the reset key, to restart the cooler. If the cooler does not resume normal operation, or the message returns, contact a service provider. When the cooler is still running but the Networker shows a fault message, pressing Key 4 may clear it. Should the fault persist, book a service.
If the cooler is not running and a different message appears, also book a service.
Which simple causes can trigger a cooler fault?
Several everyday issues can stop an evaporative cooler or upset its controls.
- The power isolation switch at the cooler may be off.
- A 10 amp fuse or circuit breaker in the meter box may have tripped.
- The water supply to the cooler may be off.
- Water in the cooler tank may sit outside its normal level range.
- A normal time delay may be running while the cooler opens, fills and pre wets its pads.
According to the Contour manual, the fan may not start straight away while the cooler opens its ServoSeal, fills the tank and pre wets the pads. That delay is normal.
How does an evaporative cooler work?
A Brivis evaporative cooler sits on the roof. Inside it, a pump lifts water from a tank and spreads it over thick filter pads. A large fan draws outside air through those wet pads, where evaporation cools it, and pushes the cooled air down through ducts to outlets in the ceiling. Warm air then leaves through open windows and doors.
Because the system relies on water, power and airflow working together, a fault in any one of them can stop the cooler.
Which checks can you make from inside?
From inside the home, you can safely check that the Networker is on and set to cooling, that the circuit breaker or fuse for the cooler is on, and that enough windows or doors are open. You can also listen for the cooler fan and look for air coming from the outlets.
Please do not climb onto the roof to inspect the cooler. Roof access is dangerous and should be left to a technician with proper safety equipment.
Why does the water supply matter?
The cooler needs a steady water supply to keep its pads wet. If the tap feeding the cooler is off, the inlet valve has failed or the water pressure is low, the tank will not fill. The cooler may then show a fault or run without cooling. During winter, many owners turn the cooler water off, so remember to turn it back on before summer.
What if the fan runs but there is no cooling?
If air comes from the outlets but it feels warm and dry, the pads may not be getting water. The pump may have failed, the water supply may be off or the distribution system may be blocked. The Contour manual suggests checking that water reaches the pads evenly. From inside, you can only check the water supply tap if it is accessible at ground level. Leave the roof checks to us.
What if no air comes from the outlets?
If the cooler seems to run but no air reaches the outlets, the fan may have a fault, a duct may have come loose or an outlet may be blocked. Check that outlets in the rooms are open and not covered. Then call us, as duct and fan problems need roof access.
Why does the fuse matter?
The Contour manual mentions checking the 10 amp fuse in the meter box. If the cooler circuit trips or the fuse blows, the cooler loses power entirely. A single trip can happen during a storm, but repeated trips suggest a fault in the cooler or its wiring. In that case, stop resetting and call a technician.
Does winter storage cause faults?
Coolers sit idle through winter, often with their water supply off and their tanks drained. In spring, pads may be dry and dusty, the pump may stick and debris may block the drain or inlet. Running the cooler for the first time without a service can trigger faults. A spring service checks the pump, pads, water supply and drain before summer.
Which Brivis evaporative coolers use the Networker?
Brivis evaporative ranges include the Contour, the Advance and the Advance Plus. Many installations use a Networker wall controller, and some homes run both a Brivis gas heater and a Brivis evaporative cooler from the same controller setup. The Brivis Touch controller also supports evaporative cooling. Fault messages appear on whichever controller the system uses.
If your home has both a heater and a cooler, check that the controller is set to cooling mode when you expect the cooler to run. A heater fault and a cooler fault show different messages.
What does the pump do, and how does it fail?
The pump lifts water from the tank to the top of the pads. Without it, the pads dry out and the cooler only blows outside air through. Pumps can fail from age, scale build up, debris in the tank or running dry. A failed pump is one of the most common reasons a cooler blows warm air.
We test the pump on site, clean its intake and replace it if needed.
How do pads affect cooling?
The pads hold the water that cools the air. Over time they collect scale, dust and debris, and their material can break down. Damaged or clogged pads cool poorly and may smell. The Contour manual suggests checking that pads are not damaged and that their material has not deteriorated. New Celdek pads can give off a mild smell at first, which fades as they are flushed during use.
What about the water level in the tank?
The tank needs water between its minimum and maximum levels. If the level drops too low, the pump may run dry. If it rises too high, water can overflow. A faulty inlet valve, a stuck float or a drain problem can upset the level. The cooler may then report a fault or stop to protect itself.
Does water quality matter?
Yes. Sydney water contains dissolved minerals that are left behind as water evaporates. Over time, those minerals form scale on pads and in the tank. Brivis coolers use water management systems, such as AquaSave on some models, to manage this. A cooler with a failing water management system may build scale quickly and lose performance.
What if a cooler fault appears after a storm?
Storms can trip breakers, cut power and occasionally damage boards or motors. In addition, strong winds can blow debris into the cooler. After a storm, check the breaker, then try one reset at the Networker. If the fault returns, book a service.
How often should a cooler be serviced?
Most owners benefit from a service before each summer. The service cleans the tank, checks the pump and pads, tests the inlet and drain, inspects the fan and motor and confirms the controls work. Our service page explains what is included.
Is the cooler covered by warranty?
Brivis evaporative coolers carry a standard warranty, and some ranges offer extended cover. Brivis does not warrant ductwork or installation, and consumables such as filters are excluded. If your cooler is fairly new, keep your purchase details handy and we can explain the next steps.
Why must windows and doors be open?
An evaporative cooler pushes a large volume of air into the home. That air needs somewhere to go. If windows and doors stay shut, pressure builds up, airflow drops and humidity rises inside. The cooler then feels weak and the air feels sticky. The Contour manual warns that too few ventilation points can cause draughts or poor air distribution.
Open windows or doors on the side of the home away from the prevailing wind, and in the rooms you want to cool. Our ventilation guide explains the best approach.
What if the humidity feels too high?
On humid days, evaporative cooling becomes less effective because the air already holds a lot of moisture. The manual suggests opening more doors and windows. If outside humidity keeps rising, run the fan only with the pump off. That moves air for comfort without adding more moisture. Sydney summers often bring humid spells, especially near the coast, so this tip is useful.
Why might moisture appear on tiles or surfaces?
If cool, moist air from an outlet blows directly onto a cool surface, such as tiles or glass, moisture can condense there. The manual suggests directing airflow across the ceiling or toward an external wall instead. Adjusting the outlet direction usually solves it.
Can a cooler fault damage the home?
Most faults simply stop the cooler. However, a tank overflow or a drain problem can sometimes send water where it should not go, such as into the roof space. If you notice water stains on the ceiling near the cooler duct, switch the cooler off and call us promptly.
How does the ServoSeal work?
Contour models use a ServoSeal, a closing mechanism that seals the cooler when it is not running. That keeps out dust, insects and cold air in winter. When the cooler starts, the ServoSeal opens before the fan runs. If the seal sticks or its motor fails, the cooler may not start properly or may report a fault. We check the seal movement during a service.
What should you tell us when you call?
Tell us the code number in the message, whether the fan runs, whether air comes from the outlets and whether it feels cool. Mention when the cooler was last serviced and whether the water supply was turned off over winter. These details help us bring the right parts.
Can the drain valve cause problems?
Many coolers drain their tank automatically after use, or at set intervals, to flush out minerals. If the drain valve sticks open, the tank cannot fill and the pads stay dry. If it sticks closed, minerals build up quickly. Either way, performance suffers and a fault may appear. Checking the drain valve is part of every cooler service.
How do we diagnose a cooler fault?
First, we confirm the message and code on the Networker. Next, we check power, the water supply and the controls. Then we go up to the roof with proper safety gear and inspect the pump, the water distribution, the tank level, the inlet valve, the drain, the fan and the motor. Finally, we explain the cause and quote before any repair.
How do you book?
Call 02 9071 1142 with the code number and what the cooler is doing, or use our contact page and we will call you back to arrange a time.
Frequently asked questions
What does a Brivis cooler fault message mean?
The evaporative cooler detected a problem and reported it to the Networker.
How do I reset a Brivis cooler fault?
Press Key 4 on the Networker. If the fault returns, book a service.
Why does the fan take a while to start?
The cooler may be opening its ServoSeal, filling the tank and pre wetting the pads.
Should I climb onto the roof to check the cooler?
No. Roof access is dangerous. Leave it to a technician.
Why is the cooler blowing warm air?
The pads may not be getting water. Check the water supply and book a service.
How do I book?
Call 02 9071 1142 or use our contact page.