Setting the Brivis Networker Program for Your Routine
The Brivis Networker program runs your heating automatically, warming the home before you wake and before you return, then easing off overnight and while you are out. Used well, it saves gas without sacrificing comfort. Used badly, it can leave you cold or heat an empty house. This guide explains the five program periods, the default times, the difference between temporary and permanent changes and how to tailor the program to your household.
What does the Brivis Networker program do?
In automatic mode, the Networker follows a daily schedule. It splits each day into five periods, each with a start time and a target temperature. When a new period begins, the controller changes the target and the heater responds. You set the schedule once, and the system follows it every day until you change it.
What are the five periods?
The periods are named Wake, Leave, Return, Presleep and Sleep. The names hint at a typical household day. Wake covers the morning routine, Leave covers the time the home is empty, Return covers the evening, Presleep covers winding down before bed and Sleep covers the night.
What are the default times?
Out of the box, Wake starts at six in the morning, Leave at nine, Return at four in the afternoon, Presleep at half past nine at night and Sleep at ten. Those defaults suit a household that leaves for work or school in the morning and returns in the late afternoon. Many households need different times.
What is the difference between temporary and permanent changes?
If you press the up or down key while the program runs, you make a temporary change. It lasts only until the end of the current period, then the program returns to its set temperature. That is handy for a chilly evening, but it can confuse owners who think the heater has ignored them when the change disappears.
To change the schedule permanently, use the Prog key and edit the period times and temperatures. Those changes stay until you edit them again.
How should you choose temperatures?
Comfort varies, yet a few principles help. Set a comfortable temperature for Wake and Return, when people are active at home. For Leave, choose a lower temperature, or let the heater rest entirely. Set a slightly lower temperature for Presleep and a lower one again for Sleep, since most people sleep better in a cooler room under warm bedding.
Each degree you lower the target saves gas over a season.
How do you match the program to your routine?
Start by writing down a typical day. When does the first person get up? At what time does the home become empty, and when does someone return? When does the household go to bed? Set each period to start a little before those times, so the home is warm when people need it.
If your routine differs on certain days, review the program settings available on your controller. Some households simply choose times that suit most days and use temporary changes for the rest.
Why does the heater start before the period begins?
It may not. The heater responds when a period begins, so if the home is very cold, it may take a while to reach the new target. Setting Wake and Return a little earlier than you need them gives the heater time to warm the home.
What happens if the clock is wrong?
The program depends on the correct time and day. After a power cut of two to three hours or more, the Networker may lose its clock. The program then runs at the wrong times. Set the clock on the master Networker after any long outage. Our power outage guide explains this.
Can the program control zones?
On zoned systems, the program can work with zones so that, for example, living areas warm during Return and bedrooms during Presleep and Sleep. Keep enough zones and outlets open in every period to protect airflow. Our zoning guide explains why.
Who can change the program in a dual controller home?
In homes with two Networkers, only the master can set the clock and the program. The slave follows the master settings.
How can you stop others changing the program?
Lock the Networker with a PIN. The factory code is 1111, and you can set your own. Locking one controller locks both in a dual controller home.
How does the program save money?
The biggest savings come from not heating an empty home and not overheating bedrooms at night. A program that drops the target during Leave and Sleep can noticeably reduce gas use over a winter. Combine it with a clean filter and sensible zone use for the best results.
When should you review the program?
Review it at the start of each winter, after daylight saving changes, when school terms or work patterns change and after any long power outage. A five minute review at those times keeps the schedule matched to real life.
What are some example programs?
Every household differs, but a few common patterns help as starting points.
A family with school aged children might start Wake at half past five, Leave at half past eight, Return at half past three, Presleep at nine and Sleep at half past nine. The early Wake period gives the heater time to warm the home before breakfast.
A couple who work from home might keep a moderate temperature through the Leave period, since the home is occupied all day, then lower it for Presleep and Sleep.
A retired household might start Wake a little later, keep a steady temperature through the day and begin Sleep a little earlier.
Adjust these to suit your own day. The key is matching heat to the times people are actually home and awake.
How warm should bedrooms be at night?
Many people sleep well in a cool room with warm bedding. Heating bedrooms to living room temperatures overnight uses a lot of gas and can make sleep less comfortable. A lower Sleep temperature, or switching bedroom zones off once everyone is in bed, often works better. On very cold nights, a slightly higher Sleep setting can stop the home becoming too cold by morning, which helps the Wake period warm up faster.
Should the heater run while you are out?
For short absences, letting the temperature drop and then warming up again on return usually saves gas compared with holding a constant temperature. For long absences, such as holidays, switch the heater off at the controller. In very cold conditions, some owners keep a low setting to take the chill off the home.
Why does the home feel cold even though the program is on?
Check the current period and its target temperature. If the program has moved into Leave or Sleep, the target may be lower than you expect. Also check that the clock is correct and that the heater is not showing a fault. If the program looks right and the heater runs but the home stays cold, see our weak heat guide.
Can you skip the program for a day?
You can switch to manual mode for the day and set the temperature you want. Remember to switch back to automatic afterwards, or the program will not resume. Some owners forget and wonder why the heater runs all night.
Does the program affect add on cooling?
On DualComfort systems, cooling can also follow a schedule, depending on the controller. In cooling mode the target logic reverses, so a higher target means less cooling. Review the cooling settings separately in late spring.
How does the program interact with modulating heaters?
StarPro 6 models and other higher efficiency heaters modulate their gas output. Instead of blasting at full power and then stopping, they reduce output as the home nears its target and hold a steady temperature. With these heaters, a steady program with gentle changes between periods tends to work well. Large jumps, such as going from a very low Leave temperature to a high Return temperature, make the heater run at full output for longer.
So with a modulating heater, consider a Leave temperature that is lower than Return but not drastically so, unless the home will be empty for many hours.
Can the program help on mild days?
On mild autumn or spring days, the program may call for heat that you do not really need. A sunny afternoon can warm the home naturally. If you find the heater running when the house already feels warm, lower the Return target for the season or switch to manual mode on mild days. Review the program again when the weather turns colder.
What if the household routine changes often?
Shift workers, families with changing schedules and people who travel often may find a fixed program frustrating. In that case, manual mode with a sensible target may suit better, combined with switching the heater off when leaving. Alternatively, newer controllers with app control let you adjust the heating remotely. Ask us whether your system can support app control through the Rinnai Touch app.
How do you check the program is working?
Watch the controller display at the start of each period over a day or two. The period name should change at the set time and the target should change with it. If the period changes but the heater does not respond, check for an error message. If the period never changes, the controller may be in manual mode or the clock may be wrong.
Should the program change with the seasons?
Yes. Early and late winter usually need lower targets and shorter heating periods than the coldest weeks of July. A quick review at the start and end of each season keeps comfort high and costs low.
Why might the heater ignore the program?
There are a few common reasons. The controller may be in manual mode rather than automatic. A temporary change may be holding until the end of the current period. A zone may be switched off for the rooms you are in. The heater may be in a fault state, with a message on the screen. Finally, in a dual controller home, a change on the master may override what you set on the slave. Work through these possibilities before assuming the heater has a fault.
How does the controller position affect the program?
The program targets are compared with the temperature the controller measures. If the controller sits in a warm spot, such as near an outlet, in afternoon sun or close to the kitchen, it may think the home is warm enough and stop heating early. Bedrooms and far rooms then stay cool. If you notice this, ask a technician about moving the controller or adding a remote temperature sensor.
Can a program help protect the heater?
Indirectly, yes. A sensible program avoids long periods of maximum output and frequent large swings in temperature. It also reduces total running hours, which slows wear on the fan, igniter and burners. Combined with regular servicing, a good program helps the heater last.
Is it worth writing the program down?
Yes. Write the period times and temperatures on a small card kept near the controller or in the manual. After a power outage, a controller replacement or an accidental change, you can restore the settings in minutes. It also helps everyone in the household understand why the heater behaves as it does through the day.
How do you get help?
If the program still does not behave as expected, call 02 9071 1142 or use our contact page.
Frequently asked questions
What are the Networker program periods?
Wake, Leave, Return, Presleep and Sleep.
What are the default times?
Wake six am, Leave nine am, Return four pm, Presleep half past nine pm and Sleep ten pm.
Why did my temperature change disappear?
Up and down changes in auto mode are temporary and end with the current period.
How do I make a permanent change?
Use the Prog key to edit the period times and temperatures.
Why is the program running at the wrong time?
The clock may have reset after a long power outage.
How do I get help?
Call 02 9071 1142 or use our contact page.