Brivis Heater Leaking Water, Where It Comes From

A Brivis heater leaking water surprises many owners, since gas heaters seem like dry appliances.

Yet several Brivis systems do handle water. Condensing heaters such as the StarPro 6 produce condensate, Brivis ICE add on cooling removes moisture from the air and evaporative coolers run on water. When drains block or fittings fail, water can appear on ceilings, walls or the ground. This page explains the sources and what to do.

Why is my Brivis heater leaking water?

The answer depends on the type of system and the season. In winter, the likely source is condensate from a condensing gas heater. In summer, it is usually condensate from add on cooling or water from an evaporative cooler. Roof leaks during rain can also look like heater leaks. Note when the water appears and which system was running.

Which Brivis heaters produce condensate?

High efficiency condensing heaters, including the StarPro 6 and the older StarPro Max, extract so much heat from the flue gases that water vapour condenses inside the heater. That water drains away through a condensate pipe to a suitable outlet. StarPro 4 and StarPro 5 models are non condensing and do not need a condensate drain.

If you have a condensing model and see water near the heater, the condensate drain is a prime suspect.

What happens when the condensate drain blocks?

If the drain pipe blocks with debris, sludge or insects, water backs up inside the heater. It may overflow from the cabinet or leak at joints. The rising water can also affect the flue path and pressure switch, causing a lockout with code 56. Turn the heater off and call us.

Where does add on cooling water come from?

Brivis ICE add on cooling uses a coil fitted with the heater. As warm, humid air passes over the cold coil, moisture condenses and drips into a tray, then drains away through a pipe. If the tray or drain blocks, water overflows. With roof heaters, that can mean water stains on the ceiling below. Turn cooling off and call us if you see stains or drips.

Can the cooling coil freeze and then leak?

Yes. Low airflow from a dirty filter, too few open outlets or a refrigerant shortage can make the coil ice up. When the ice melts, the drain may not cope with the sudden flow, and water overflows. Clean the filter, open outlets and see our cooling mode guide.

Can evaporative coolers leak?

Evaporative coolers on the roof hold water in a tank and wet their pads continuously. A faulty float valve, a stuck drain valve, a cracked tank or a blocked overflow can send water where it should not go. Water stains around a ceiling outlet from an evaporative cooler need prompt attention. Our evaporative cooling page covers coolers.

Could it be a roof leak instead?

Water appearing only during rain, especially near a flue penetration or cooler opening in the roof, may come from flashing around those openings rather than the heater itself. Flues and coolers pass through the roof, and the seals around them can age. A roofer or technician can check the flashing.

What should you do right away?

Turn off the system that seems to be leaking. Place a bucket or towels under drips, and move furniture, rugs and electronics out of the way so they stay dry while you wait for help. If water is near light fittings or power points, switch off that circuit at the switchboard. If the ceiling sags or bulges with water, keep people away and call for help promptly, as wet plaster can collapse.

Where should condensate drain to?

Condensate from heaters and cooling coils should run through a pipe to a suitable outlet, such as a drain, a gully or another approved point. It should not discharge onto paths, against foundations or into garden beds where it could pool. Condensate from gas heaters is mildly acidic, so drains should be made from suitable materials. If your condensate pipe ends somewhere odd, mention it at the next service.

Can a condensate pump fail?

Some installations cannot drain by gravity and use a small pump to lift water away. If the pump fails, loses power or clogs, water backs up quickly. Signs include water around the heater, a pump that hums without moving water or a pump that runs constantly. A technician can clean, test or replace the pump.

Why do leaks often appear at the start of a season?

Over the off season, drains dry out, dust settles and insects or spiders nest in pipes and traps. When the system starts again, the first water meets a blocked drain. Running a short test before the season, and checking that water drains away, catches these blockages early. For heaters, our winter start up checklist includes the condensate outlet.

Can a leak damage the heater?

Yes. Water inside a heater can corrode the cabinet, affect electrical parts and upset the flue path. Water around a roof heater can soak insulation and ceilings. Acting quickly limits the damage. Do not run the system again until the source is fixed.

Is a little water near an external heater normal?

On condensing external heaters, a small amount of condensate drips from the drain outlet during operation, which is normal. Water pooling under the cabinet, running from seams or dripping from the flue in large amounts is not normal.

Are leaks covered by warranty?

If a heater part fails, such as a cracked internal trap on a young condensing heater, warranty may apply. Blocked drains from debris and installation issues, such as drain pipes without enough fall, usually do not fall under the product warranty. Brivis does not warrant ductwork or installation. Home insurance may cover resulting water damage, depending on your policy.

How can you prevent leaks?

Keep filters clean so coils do not freeze, check condensate outlets at the start of each season, keep the area around drains clear of mulch and leaves and book regular servicing. For evaporative coolers, a service before summer checks the float, drain valve, tank and overflow.

How can you trace where the water comes from?

Start by noting where the water appears and when. A ceiling stain directly below a roof heater that grows in winter points to the heater condensate. A stain below the heater that grows in summer points to the add on cooling coil. Drips near a ceiling outlet in summer, in a home with an evaporative cooler, point to the cooler. Stains that grow only during rain point to the roof.

Next, check the condensate outlet outside, if you know where it is. A dry outlet while the heater or cooling runs suggests a blockage somewhere upstream. A steady drip suggests the drain works and the leak lies elsewhere.

What does water near an underfloor heater mean?

Underfloor heaters sit in the subfloor, where water from leaking plumbing, poor drainage or heavy rain can collect. Water near the heater may not come from the heater at all. However, water and gas heaters do not mix well, so turn the heater off and arrange a check. A technician can confirm whether the heater is the source and whether it has suffered any damage.

Can water reach the electrical parts?

Yes. Water that overflows inside a heater can reach the control board, fan motor or wiring. That can cause faults, tripped breakers or damage. If the heater has been wet, do not run it until a technician has checked it.

What about water stains around ceiling outlets in winter?

In winter, a stain around a heating outlet is less common. It may come from a roof leak near the duct, condensation forming on a poorly insulated duct in a cold roof or a condensing heater draining badly nearby. A technician can check the duct insulation and the heater drain.

How long does a leak repair take?

Clearing a blocked drain or trap is usually quick. Replacing a pump, a tray or a damaged pipe section takes a little longer. If the coil has frozen because of a refrigerant shortage, the leak repair and recharge add time. Our gas and regas page explains refrigerant work.

What should you tell us when you call?

Tell us where the water is, which system was running, the heater model and whether any codes appear. Photos of stains and the condensate outlet help. Mention whether the water appears only in rain or only when the system runs. Also tell us how long the leak has been happening and whether the ceiling feels soft, so we can judge how urgent the visit is and bring the right equipment.

Why does a condensing heater make so much water?

Burning gas produces water vapour. A standard heater sends most of that vapour out through the flue as a warm gas. A condensing heater cools the flue gases further to capture extra heat, and as they cool, much of the vapour turns into liquid inside the heater. On a long cold night, that can add up to a surprising volume. That water is a sign the heater is working efficiently, as long as it drains away properly.

Why does add on cooling produce water?

Refrigerated cooling removes moisture from the air as well as heat. On humid Sydney days, the coil can collect a lot of water, which drips into the tray and flows down the drain. The more humid the day, the more water the system removes. If the drain cannot keep up, or if it is partly blocked, overflow follows.

Can a leak cause mould?

Yes. Water that soaks ceilings, insulation or timber can encourage mould growth, which can cause musty smells and health concerns. Dry the area promptly with fans and ventilation, fix the source and consider having damaged ceiling sections replaced. Ongoing dampness is worth addressing quickly.

How do you protect the ceiling below a roof heater?

Many installations place a safety tray under roof mounted equipment to catch overflow. If your heater or cooling coil sits above living areas without a safety tray, ask a technician whether one can be fitted. A tray with its own drain or an overflow switch adds an extra layer of protection against ceiling damage.

What if the leak is from the evaporative cooler drain line?

Evaporative coolers drain water to flush minerals from the tank. That drain line should run to a suitable outlet. If it cracks, disconnects or blocks, water can run onto the roof, into gutters or into the roof space. A technician can check the drain line and valve during a service.

Is it safe to keep using the system while it leaks?

Generally, no. A heater with a blocked condensate drain may lock out, and water inside can damage parts. A cooling coil that overflows will keep doing so every time cooling runs. An evaporative cooler with a faulty float can waste water and damage ceilings. Switch the system off and use other safe heating or cooling until the source is fixed. The small inconvenience now prevents larger repair bills later.

What will a technician check?

A technician identifies the source, then checks condensate drains, trays, pumps, fittings, coils, the flue and roof penetrations as needed. They clear blockages, repair or replace damaged parts and test the drainage. They explain the cause and quote before repairs.

How do you book?

Call 02 9071 1142 or use our contact page. We can usually trace and fix the leak in one visit, and we will explain any ceiling or insulation damage we notice while we are there.

Frequently asked questions

Why is my Brivis heater leaking water?

Condensate from a condensing heater or add on cooling, or water from an evaporative cooler.

Do StarPro 5 heaters produce condensate?

No. StarPro 4 and 5 models are non condensing.

Can a blocked condensate drain cause a code?

Yes. It can cause a code 56 lockout on condensing models.

Why are there stains on the ceiling in summer?

Add on cooling or evaporative cooler water may be overflowing.

What should I do first?

Turn the system off, catch drips and switch off nearby circuits if water is near electrics.

How do I book?

Call 02 9071 1142 or use our contact page.

{“@context”:”https://schema.org”,”@type”:”HVACBusiness”,”@id”:”https://brivis.sydneyaircare.com.au/#business”,”name”:”Sydney Air Care, Brivis Service”,”url”:”https://brivis.sydneyaircare.com.au/”,”description”:”Brivis ducted heating and cooling repair, service and troubleshooting across Sydney. Independent service provider, not affiliated with Brivis.”,”areaServed”:[{“@type”:”City”,”name”:”Sydney”},{“@type”:”State”,”name”:”New South Wales”}],”parentOrganization”:{“@type”:”Organization”,”name”:”Sydney Air Care”,”url”:”https://sydneyaircare.com.au/”},”telephone”:”+61 2 9071 1142″} {“@context”:”https://schema.org”,”@type”:”FAQPage”,”mainEntity”:[{“@type”:”Question”,”name”:”Why is my Brivis heater leaking water?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Condensate from a condensing heater or add on cooling, or water from an evaporative cooler.”}},{“@type”:”Question”,”name”:”Do StarPro 5 heaters produce condensate?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”No. StarPro 4 and 5 models are non condensing.”}},{“@type”:”Question”,”name”:”Can a blocked condensate drain cause a code?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Yes. It can cause a code 56 lockout on condensing models.”}},{“@type”:”Question”,”name”:”Why are there stains on the ceiling in summer?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Add on cooling or evaporative cooler water may be overflowing.”}},{“@type”:”Question”,”name”:”What should I do first?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Turn the system off, catch drips and switch off nearby circuits if water is near electrics.”}},{“@type”:”Question”,”name”:”How do I book?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Call 02 9071 1142 or use our contact page.”}}]}
Call 02 9071 1142