Brivis Heater Not Heating Properly, Causes and Fixes
A Brivis heater not heating properly is often more frustrating than one that will not start. The burners light, the fan runs and air flows from the outlets, yet the home never quite gets warm. Lukewarm air, slow warm up and rooms that lag behind each have common causes. This guide explains how to tell normal behaviour from a fault, what you can check and what a technician looks for.
What does Brivis heater not heating properly look like?
Owners describe it in different ways. The air feels warm but not hot. The home takes hours to reach the set temperature, or never reaches it. Some rooms feel fine while others stay cold. The heater runs almost constantly on cold nights. Each description gives a clue, so note which one fits your situation.
Is it normal for the air to feel only warm?
Partly, yes. Ducted gas heaters deliver large volumes of warm air rather than small streams of very hot air. Higher efficiency models, such as the StarPro 6 with its modulating gas valve, deliberately reduce output as the home nears its target and hold a steady temperature. The air from the outlets may then feel gently warm rather than hot. That is efficient, comfortable heating, not a fault.
The question is whether the home reaches and holds the set temperature. If it does, the heater is working.
Which settings cause weak heat?
Start with the controller. Check the set temperature for the current period, especially if the program has moved into Leave, Presleep or Sleep with a lower target. Make sure continuous fan is not running between heating cycles in a way that feels cool. Confirm the zones for the rooms you are in are switched on. Our auto program guide explains the periods.
How does airflow affect warmth?
A clogged return air filter, closed outlets or blocked registers reduce airflow. Less airflow means less heat delivered to the rooms. Sometimes it also makes the heater overheat and cycle off, so the home cools between bursts of warmth. Clean the filter, open outlets and clear registers first. Our filter guide and outlet guide explain how.
How do ducts cause weak heat?
Ducts run through roofs and subfloors, often in very cold spaces in winter. If a duct is disconnected, torn or crushed, warm air escapes into the roof or under the floor instead of reaching the room. If duct insulation is damaged, warm air loses heat on the way. Rooms at the end of long duct runs suffer most. A technician can inspect the ducts and repair damage.
How do burners and gas pressure affect output?
Dirty burners and low gas pressure reduce the heat the burners produce. The flame may be weak, uneven or lazy. Low pressure can come from the supply, an undersized gas line or other appliances running at the same time. A technician cleans the burners and measures gas pressure at the heater during a service.
Can the heater be too small?
Sometimes. If a heater was sized for a smaller home and the house has since been extended, or if insulation is poor, the heater may not keep up on very cold nights. Brivis heaters range from about 15 to 35 kilowatts depending on the model. A technician can assess whether the heater suits the home.
How does the controller position matter?
If the controller sits in a warm spot, it may reach its target early and turn the heater down while other rooms are still cool. Common warm spots include near an outlet, in afternoon sun or close to the kitchen. Moving the controller or adding a remote sensor can help.
Why does the heater run constantly but rooms stay cool?
Constant running with little warmth points to heat escaping somewhere. Disconnected ducts, open windows, poor insulation or a home that is too large for the heater are likely causes. In some cases, a weak fan delivers too little air. A technician can measure airflow and temperature at the outlets to narrow it down.
Does insulation affect how warm the home gets?
Yes, a great deal. A heater replaces the heat the home loses through its roof, walls, windows and floor. Homes with little ceiling insulation, single glazed windows and draughty doors lose heat quickly, so the heater must work harder and may still fall short. Simple improvements, such as door seals, heavy curtains and topping up ceiling insulation, often make the existing heater feel much stronger.
Do open fireplaces and exhaust fans matter?
An open fireplace chimney and running exhaust fans can draw warm air out of the home. If the heater struggles, check that the fireplace damper is closed when not in use and that bathroom and kitchen fans are not running for long periods. Every bit of warm air that escapes must be replaced.
Why might the first hour feel weak?
On a cold morning, the walls, floors and furniture are all cold. The heater must warm them as well as the air, so the first hour can feel slow. Starting the Wake period a little earlier gives the heater time to catch up. Once the home is warm, the heater only needs to maintain it, which is easier.
Can a cracked heat exchanger reduce heat?
A cracked heat exchanger is primarily a safety concern rather than a performance one, since it can let combustion gases mix with house air. It may not obviously reduce warmth. That is why a technician inspects the heat exchanger during a service. If any crack is found, the heater should not run until the problem is resolved.
Does a dirty fan reduce warmth?
Yes. A fan wheel coated with dust moves less air. The heater may still produce heat, but less of it reaches the rooms, and the heat exchanger may run hotter. Cleaning the fan wheel during a service restores airflow.
Can zones make the home feel weaker?
If you switch off zones to save gas, the rooms in those zones cool down, and walking through them can make the whole home feel cold. In addition, cold rooms pull warmth from neighbouring heated rooms through walls and doors. Keeping doors to unheated areas closed helps.
When does weak heat suggest a safety issue?
Weak heat on its own is usually a comfort issue. However, if weak heat comes with a strange smell, sooting around outlets or the flue, headaches or dizziness in the household, or a yellow or lazy flame visible through any inspection window, turn the heater off and call us. Those signs can point to combustion problems.
How do you measure whether the heater is weak?
A simple kitchen or digital thermometer helps. Hold it in the airflow at an outlet near the heater and at one far away, after the heater has run for fifteen minutes. Note both readings and the room temperature. A large drop between the near and far outlet suggests duct losses. Similar readings that both feel lukewarm suggest a heater output or airflow issue. Share these numbers with the technician, as they speed up diagnosis.
Why is upstairs warmer than downstairs?
Warm air rises, so upper floors often feel warmer than lower ones in two storey homes. If the controller sits upstairs, it may reach its target while downstairs stays cool. Zoning, a remote sensor downstairs or adjusting outlet balance can even this out. Floor registers downstairs help too, because they deliver warmth at foot level.
Why are some rooms colder on windy nights?
Wind increases heat loss through gaps around windows and doors and cools external walls. Rooms on the windward side of the home feel it most. In addition, ducts in a draughty subfloor or roof lose more heat when cold air moves around them. Sealing gaps and checking duct insulation can help.
Can the fan speed setting reduce warmth?
Yes. If the fan runs too fast for the heater output, air leaves the outlets in large volumes but feels cooler. If it runs too slowly, the heater may overheat and cycle. On StarPro models, installers can choose from many fan speeds. A technician can check whether the current setting suits your ducts and home.
Does the heater star rating affect warmth?
The star rating describes efficiency, not how hot the air feels. A 6 star heater turns more of its gas into useful heat than a 3 star heater, but both can warm a home if sized correctly. Higher efficiency models often run longer at lower output, which can feel gentler. Each step up in star rating reduces annual energy use by roughly ten percent, according to Brivis.
Why does the home cool quickly when the heater stops?
Fast cooling suggests the home loses heat quickly, through poor insulation, draughts or large windows. The heater may be doing its job, but the home cannot hold the warmth. Improving insulation and sealing draughts often helps more than any heater repair.
Should you increase the set temperature?
Raising the set temperature makes the heater run longer, but it does not make the air from the outlets any hotter on most models. If the home never reaches a moderate target, the cause lies elsewhere. Find and fix the cause rather than pushing the target higher, which only raises running costs.
Does a service restore lost performance?
Often. A service cleans the burners, flame sensor and fan wheel, checks gas pressure and confirms the fan setting. Many owners notice warmer air and faster warm up afterwards, especially if the heater had not been serviced for several years. Brivis recommends servicing at least every two years. Our service page explains the visit.
How do renovations affect warmth?
Renovations often change how a ducted system performs. A new extension may have been added without extra outlets, walls may have moved so outlets now sit in odd spots, or ducts may have been squashed by new ceiling framing. Floor coverings can partly cover floor registers. If the home felt warm before renovations and weaker afterwards, mention the work when you call. The fix may be as simple as reconnecting a duct or adding an outlet.
Can you improve warmth without repairs?
Yes, in many homes. Close curtains at dusk, use door snakes at the bottom of external doors and keep internal doors to unused rooms closed. Make sure furniture does not cover outlets or the return grille. Clean the filter every fortnight. Each step helps the existing heater feel stronger without spending anything on repairs or new parts.
What should you tell us when you call?
Tell us which rooms feel weak, how long the heater takes to warm the home, the set temperature and whether the problem is new or has always existed. Mention any renovations, zone changes or recent work in the roof or subfloor. Thermometer readings from outlets are a great bonus, because they turn a vague feeling of weak heat into numbers we can compare on site.
What will a technician check?
A technician checks the controller and settings, the filter and outlets, the fan speed and motor, the burners and gas pressure, the heat exchanger, the ducts and the zone dampers. They measure the temperature of the air leaving the heater and at several outlets. Then they explain the cause and quote before any repair.
How do you book?
Call 02 9071 1142 or use our contact page. In addition, have your heater model and the approximate age of the system ready, as both help us plan the visit and bring the right parts. Meanwhile, keep the filter clean and outlets clear so the heater can do its best until we arrive.
Frequently asked questions
Is it normal for Brivis air to feel only warm?
Yes, especially on modulating models that hold a steady temperature.
What should I check first for weak heat?
Set temperature, program period, zones, filter and outlets.
Can damaged ducts cause weak heat?
Yes. Disconnected or torn ducts leak warm air into the roof or subfloor.
Can low gas pressure reduce heat?
Yes. A technician measures pressure at the heater.
Can the controller position matter?
Yes. A controller in a warm spot may turn the heater down too early.
How do I book?
Call 02 9071 1142 or use our contact page.